- Manufacturing & Industrial News Portal

Home | Submit News | Your Account | Today's Headlines | Free Magazines | Support

International News: Tips on Attaching Sill Plates to Concrete Foundations #18100
Posted by:
City: Cleveland
State: Ohio
Postal code: 44114
Country: United States
Telephone: 4074327706
Company: Concrete Fasteners Systems
Website URL:
Contact Email:

click to view fullsize image
News Article:
When building a new structure, it is critical to securely fasten items to the foundation or slab of concrete with the use of a sill plate. A sill plate, also known as a sole plate, is the bottom horizontal part of a wall or building to which the vertical studs will be attached.

Most sill plates are made from lumber - usually measuring 2x4, 2x6, 2x8 or 2x10.

Before Getting Started

To ensure proper construction and safety, it is important to determine which fastening system will be the best choice for attaching the sill plates.

One method for fastening sill plates is the use of cast-in-place anchors, commonly referred to as "J" Bolts. "J" bolts are anchors in the shape of the letter J with threads on the end opposite of the bent end. These bolts are set in place before the concrete is poured.

The use of "J" bolts provides the best holding values, but can be problematic for the do-it-yourselfer due to the expertise needed for the complicated installation steps. The "J" bolts must be installed completely perpendicular and, if not, numerous problems will occur when trying to attach the sill plate. Also, this method cannot be used when building a structure where there is an existing foundation, such as replacing a dilapidated garage.

For less complicated applications or for those with existing foundations, Wedge Anchors are a type of concrete anchor that can be successfully used with sill plates. This type of anchor is a post-installed anchor, meaning that it is placed in concrete after it is fully cured. These fasteners are designed for use in solid concrete only. Wedge anchors are available in diameters measuring from 1/4" to 1 1/4".

The length of the wedge anchor is completely dependent upon the thickness of the material to be fastened. To determine the size of anchor needed, it is important to check local building codes or to consult with an engineer or architect. It is also critical to verify the holding values required for your particular application since the quality of concrete may widely vary.

Choosing the Required Size Wedge Anchors

Once the required holding values have been determined, use the li nk to the

wedge anchor sizing chart to determine the appropriate diameter and length for the wedge anchors.

1-Other considerations when using wedge anchors include: Use a wedge anchor of suitable length for the specific application

2-Which is calculated by using the equation below: Minimum em bedment for the diameter being used. Thickness of the material being fastened, thickness of the nut and washer equals Minimum length of the wedge anchor needed.

3-Ensure that the anchor will be further than the minimum distance from the concrete edge. The rule of thumb is a minimum of five anchor diameters from the unsupported edge of the concrete.

For example, if your wedge anchor is 1/2" in diameter, it must be installed a minimum of 2 1/2" from the unsupported edge.

Determine the grade of steel and/or plating of the wedge anchor required for the specific application. Wedge anchors are available in three different finishes: zinc plated, hot-dipped galvanized, and stainless steel

Helpful Hint : It is critical to remember that hole diameter is equal to anchor diameter.

This information will affect the holding values of your wedge anchors.

Step by Step Instructions

Concrete Wedge Anchors can be now be installed easily:

1- On the concrete, mark where your holes will be drilled. Remember that anchors must be placed a minimum of five anchor diameters from any unsupported edge, and there should be a minimum of ten anchor diameters between any two anchors.

2- Using a hammer drill, drill your holes using a carbide-tipped masonry bit.

The hole diameter should be the same diameter as the wedge anchor.

3- Clear the hole of all debris using compressed air, a shop-vac or wire brush.

4- Before inserting the wedge anchor into the hole, be sure to place the washer on the head and thread the nut a couple of turns. By not fully threading the nut, the threads of the wedge anchor are protected.

5- Carefully place the sill place in the correct position and insert the wedge anchors into each hole through the sill plate.

6- Hammer anchors into every hole ensuring that they are installed to the desired depth and securely in place. This will be the supporting plate to which studs will be placed later in the renovation process. Secure placement is important for the overall safety of the structure.

7- Using a torque wrench, tighten every nut to guarantee they are tightened to the required torque value.

Final Checks : When using concrete wedge anchors, it is important to remember:

*Wedge anchors are very effective when the concrete is in

good condition and minimum edge distances and spacing are maintained.

*Hole size is critical to the holding values of the wedge anchor.

*Hole diameter is equal to the anchor diameter when using

ANSI standard carbide bits.

*The tolerances of ANSI standard bits are specifically matched to work well with wedge anchors.

Finally, wedge anchors have a required torque value. Check our website for important anchor technical information page to determine the diameter of the anchor to use for a range of required torque values.

Values shown are average ultimate values and are offered only as a guide and are not guaranteed.

A safety factor of 4:1 or 25% is generally accepted as a safe working load.

Reference should be made to applicable codes for the specific working ratio.

To order online:

Home | Submit News | Your Account | Today's Headlines | Free Magazines | Support